# How Deep Will My Well Be? Well Depths in Spokane, Stevens and Lincoln Counties

URL: https://springcreekdrilling.com/guide/how-deep-will-my-well-be/
Last updated: 2026-11-01

How deep are wells in Spokane, Stevens and Lincoln counties? Median depths by county and town from state well records, why they vary, and casing depth.

10 min read Updated November 1, 2026

How deep are wells around here? In Spokane, Stevens and Lincoln counties, 65% of the state's well reports that list a depth are between 100 and 400 feet, and the median well is 200 feet deep in Spokane County, 194 in Stevens and 233 in Lincoln. Your own well could land outside that range, though, because depth can change a lot between neighbors. The wells closest to your land are the best guide, and below we show how to find them.

## Average Well Depth by County and Town

These numbers come from the 40,024 water well reports filed with the Department of Ecology for the three counties ([records through February 2025](https://fortress.wa.gov/ecy/gispublic/DataDownload/WR%5FGEO%5FWellReports.htm)). We use the median, the middle well if you lined them all up by depth, because a few very deep wells would pull an average up. The figures include farm and public supply wells, and each report is grouped with the nearest community within 10 miles.

### Spokane County

Across 24,567 reports, the median well is 200 feet deep, half are between 120 and 320 feet, and one in ten goes past 480 feet. The median by community, shallowest first (more on [drilling in Spokane County](https://springcreekdrilling.com/well-drilling/spokane-county/)):

- [Medical Lake](https://springcreekdrilling.com/well-drilling/medical-lake-wa/): 130 feet
- [Deer Park](https://springcreekdrilling.com/well-drilling/deer-park-wa/): 160 feet
- [Four Lakes](https://springcreekdrilling.com/well-drilling/four-lakes-wa/): 165 feet
- [Marshall](https://springcreekdrilling.com/well-drilling/marshall-wa/): 165 feet
- [Spokane](https://springcreekdrilling.com/well-drilling/spokane-wa/): 175 feet
- [Airway Heights](https://springcreekdrilling.com/well-drilling/airway-heights-wa/): 180 feet
- [Cheney](https://springcreekdrilling.com/well-drilling/cheney-wa/): 180 feet
- [Elk](https://springcreekdrilling.com/well-drilling/elk-wa/): 180 feet
- [Colbert](https://springcreekdrilling.com/well-drilling/colbert-wa/): 187 feet
- [Chattaroy](https://springcreekdrilling.com/well-drilling/chattaroy-wa/): 190 feet
- [Spokane Valley](https://springcreekdrilling.com/well-drilling/spokane-valley-wa/): 195 feet
- [Mead](https://springcreekdrilling.com/well-drilling/mead-wa/): 200 feet
- [Nine Mile Falls](https://springcreekdrilling.com/well-drilling/nine-mile-falls-wa/): 200 feet
- [Valleyford](https://springcreekdrilling.com/well-drilling/valleyford-wa/): 225 feet
- [Fairfield](https://springcreekdrilling.com/well-drilling/fairfield-wa/): 238 feet
- [Spangle](https://springcreekdrilling.com/well-drilling/spangle-wa/): 240 feet
- [Otis Orchards](https://springcreekdrilling.com/well-drilling/otis-orchards-wa/): 250 feet
- [Newman Lake](https://springcreekdrilling.com/well-drilling/newman-lake-wa/): 360 feet
- [Mica](https://springcreekdrilling.com/well-drilling/mica-wa/): 400 feet

### Stevens County

Across 11,266 reports, the median well is 194 feet deep, half are between 100 and 317 feet, and one in ten goes past 468 feet. The median by community, shallowest first (more on [drilling in Stevens County](https://springcreekdrilling.com/well-drilling/stevens-county/)):

- [Ford](https://springcreekdrilling.com/well-drilling/ford-wa/): 130 feet
- [Springdale](https://springcreekdrilling.com/well-drilling/springdale-wa/): 149 feet
- [Clayton](https://springcreekdrilling.com/well-drilling/clayton-wa/): 160 feet
- [Colville](https://springcreekdrilling.com/well-drilling/colville-wa/): 171 feet
- [Chewelah](https://springcreekdrilling.com/well-drilling/chewelah-wa/): 180 feet
- [Northport](https://springcreekdrilling.com/well-drilling/northport-wa/): 180 feet
- [Valley](https://springcreekdrilling.com/well-drilling/valley-wa/): 180 feet
- [Loon Lake](https://springcreekdrilling.com/well-drilling/loon-lake-wa/): 198 feet
- [Addy](https://springcreekdrilling.com/well-drilling/addy-wa/): 200 feet
- [Tumtum](https://springcreekdrilling.com/well-drilling/tumtum-wa/): 220 feet
- [Kettle Falls](https://springcreekdrilling.com/well-drilling/kettle-falls-wa/): 245 feet
- [Hunters](https://springcreekdrilling.com/well-drilling/hunters-wa/): 270 feet

### Lincoln County

Across 2,686 reports, the median well is 233 feet deep, half are between 140 and 385 feet, and one in ten goes past 562 feet. The median by community, shallowest first (more on [drilling in Lincoln County](https://springcreekdrilling.com/well-drilling/lincoln-county/)):

- [Harrington](https://springcreekdrilling.com/well-drilling/harrington-wa/): 143 feet
- [Edwall](https://springcreekdrilling.com/well-drilling/edwall-wa/): 147 feet
- [Davenport](https://springcreekdrilling.com/well-drilling/davenport-wa/): 159 feet
- [Sprague](https://springcreekdrilling.com/well-drilling/sprague-wa/): 160 feet
- [Creston](https://springcreekdrilling.com/well-drilling/creston-wa/): 180 feet
- [Reardan](https://springcreekdrilling.com/well-drilling/reardan-wa/): 180 feet
- [Wilbur](https://springcreekdrilling.com/well-drilling/wilbur-wa/): 240 feet
- [Odessa](https://springcreekdrilling.com/well-drilling/odessa-wa/): 368 feet

How the wells in each county spread out by depth:

- **Under 100 feet:** 16% in Spokane, 24% in Stevens, 11% in Lincoln
- **100 to 200 feet:** 33% in Spokane, 27% in Stevens, 30% in Lincoln
- **200 to 300 feet:** 21% in Spokane, 18% in Stevens, 23% in Lincoln
- **300 to 400 feet:** 14% in Spokane, 14% in Stevens, 13% in Lincoln
- **400 to 600 feet:** 12% in Spokane, 13% in Stevens, 15% in Lincoln
- **600 feet or deeper:** 4% in Spokane, 4% in Stevens, 9% in Lincoln

As for how deep a home well can go, drilled wells "can be drilled more than 1,000 feet deep" ([USGS](https://www.usgs.gov/special-topics/water-science-school/science/groundwater-wells)), and 1,802 wells on file here, about 5%, go 600 feet or deeper. For each town's middle range and water level, see [well depths by town](https://springcreekdrilling.com/well-drilling/).

## Why Well Depth Varies So Much Here

A well goes as deep as it takes to reach enough water, and the ground under our three counties varies a lot. Community medians run from 130 feet around [Medical Lake](https://springcreekdrilling.com/well-drilling/medical-lake-wa/) to 400 feet around [Mica](https://springcreekdrilling.com/well-drilling/mica-wa/) in Spokane County, 130 to 270 feet in Stevens and 143 to 368 feet in Lincoln. Here's what's underneath (our [guide to groundwater](https://springcreekdrilling.com/guide/a-comprehensive-guide-to-groundwater/) goes deeper):

- **Basalt** underlies Lincoln County, the West Plains around [Cheney](https://springcreekdrilling.com/well-drilling/cheney-wa/) and [Airway Heights](https://springcreekdrilling.com/well-drilling/airway-heights-wa/), and much of southern and western Spokane County. USGS describes its aquifers as "permeable interflow zones separated by less permeable flow interiors" ([USGS SIR 2011-5124](https://pubs.usgs.gov/sir/2011/5124/)): water moves mostly through the zones between old lava flows, and those sit at different depths from place to place.
- **Stevens County** has glacial sand and gravel in the valleys, but in most of the Colville River watershed "bedrock is present at or near land surface," and it "typically has very low permeabilities, except where it is fractured" ([USGS SIR 2004-5237](https://pubs.usgs.gov/sir/2004/5237/section3.html)). A valley well and a hillside well a mile apart can be very different.
- **The Little Spokane area** around [Deer Park](https://springcreekdrilling.com/well-drilling/deer-park-wa/), [Colbert](https://springcreekdrilling.com/well-drilling/colbert-wa/) and [Chattaroy](https://springcreekdrilling.com/well-drilling/chattaroy-wa/) has a sand and gravel aquifer averaging about 70 feet thick over silt, clay, basalt in places and crystalline bedrock ([USGS SIR 2013-5124](https://pubs.usgs.gov/publication/sir20135124)). A well may finish in the gravel or have to continue into the rock.
- **The Spokane Valley** sits on the gravel of the Spokane Valley-Rathdrum Prairie aquifer, yet half the wells around [Spokane Valley](https://springcreekdrilling.com/well-drilling/spokane-valley-wa/) are between 103 and 400 feet deep.

## Well Depth vs. Casing Depth, Water Level and Pump Setting

A well report lists several depths that are easy to mix up. State rules require it to show the well depth, the "total depth of casing" and, for a well that doesn't flow on its own, "the depth to the static water level, as measured below the land surface" ([WAC 173-160-141](https://app.leg.wa.gov/WAC/default.aspx?cite=173-160-141)).

- **Total depth:** from the ground to the bottom of the hole. It's what our town numbers measure, and what drives the cost of drilling.
- **Casing depth:** how far down the steel or plastic pipe lining the hole goes. It's often less than the total depth.
- **Static water level:** where the water settles when nothing is pumping, usually far above the bottom of the well. Across the reports that list one, the median is 65 feet below the ground in Spokane County, 60 in Stevens and 100 in Lincoln.
- **Pump setting:** where the pump hangs, below the water level. It's set using the well's depth, water level and yield. Pumping lowers the water in a well, and "When water levels drop below the levels of the pump intakes, then wells will begin to pump air" ([USGS](https://www.usgs.gov/special-topics/water-science-school/science/groundwater-wells)). That's one reason a well goes past the first sign of water.

### How deep does well casing go?

There's no single number. In a drilled well, the seal around the casing has to reach at least 18 feet below the surface ([WAC 173-160-231](https://app.leg.wa.gov/WAC/default.aspx?cite=173-160-231)), so the casing goes at least that far. Below that, it depends on the ground. A well can be finished with a screen, perforated pipe or an open bottom, and an open bottom "is appropriate where the withdrawn waters are essentially free of sand, silt and turbidity" ([WAC 173-160-191](https://app.leg.wa.gov/WAC/default.aspx?cite=173-160-191)). So in loose sand and gravel, the casing usually runs down to the water, often with a screen at the bottom to keep sediment out. In firm rock, the hole below the casing can stay open, and the casing may stop far short of the total depth.

Ecology's homeowner's guide suggests asking your driller about both numbers: the "estimated depth of well to be cased" and the "estimated total depth of well" ([Ecology publication 96-90](https://apps.ecology.wa.gov/publications/documents/swr9690.pdf)).

## How Deep Should a Well Be for Drinking Water?

Deep enough to reach water that will reliably supply the house, with room below the water level for the pump, and sealed so nothing from the surface gets in. The state's rules set goals rather than a number: each well must be adapted to the geology and groundwater at the site, must not be "a conduit for contaminating the groundwater or surface water," and must yield, where obtainable, the water the owner needs ([WAC 173-160-161](https://app.leg.wa.gov/WAC/default.aspx?cite=173-160-161)).

### Is a deeper well better?

Not automatically. Depth puts distance between your water and the surface, but in a drilled well much of the protection comes from the casing and its seal: "Along with grout, the casing keeps dirt and excess water out of the well" ([USGS](https://www.usgs.gov/special-topics/water-science-school/science/groundwater-wells)). Once a well reaches a good water zone and is properly sealed, extra depth mostly adds:

- **Cost.** Depth is the biggest factor in [what drilling costs](https://springcreekdrilling.com/guide/the-cost-of-drilling-a-well/), and a deeper well generally needs a more powerful pump.
- **No promise of more water.** Besides Stevens County's bedrock, Ecology says that in the Hangman Creek watershed, around [Valleyford](https://springcreekdrilling.com/well-drilling/valleyford-wa/), [Spangle](https://springcreekdrilling.com/well-drilling/spangle-wa/) and [Fairfield](https://springcreekdrilling.com/well-drilling/fairfield-wa/), "availability and yield of groundwater from bedrock in this WRIA is very limited" ([Ecology WRIA 56 summary](https://apps.ecology.wa.gov/publications/documents/2011056.pdf)).
- **No promise of cleaner water.** The state Department of Health says groundwater in Spokane and Stevens counties has potential for elevated uranium "because of naturally occurring uranium in the rock and soil" ([DOH](https://doh.wa.gov/sites/default/files/legacy/Documents/Pubs/331-056.pdf)). Only testing tells you what's in your water; see [testing a new well](https://springcreekdrilling.com/guide/testing-a-new-well/).

**The short answer:** the right depth is wherever your well reaches enough good water and can be properly sealed. The ground decides it, not a target number.

## Are Newer Wells Deeper?

In two of our three counties, yes. Wells drilled since 2015 have a median depth of 240 feet in Spokane County and 239 in Stevens, against 180 and 170 feet for wells drilled before 2000. Lincoln County is the exception, at 221 feet for newer wells against 231 before 2000. Town by town, newer wells are deeper around 30 of the 31 communities with enough reports to compare. Two things help explain it:

- **Where people are building.** Around [Chattaroy](https://springcreekdrilling.com/well-drilling/chattaroy-wa/) and [Spokane Valley](https://springcreekdrilling.com/well-drilling/spokane-valley-wa/), for example, much of the new drilling is in the parts of the area where wells run deeper; those pages show where.
- **Falling water levels.** USGS found that levels fell in 83% of the 470 Columbia Plateau wells it measured from 1984 to 2009, by more than 25 feet in 29% of them, with large and widespread declines in the Odessa Subarea ([USGS Fact Sheet 2015-3063](https://pubs.usgs.gov/fs/2015/3063/)). Ecology lists groundwater on "the West Plains plateau, southwest of the Spokane River" as in decline ([Ecology WRIA 34 summary](https://apps.ecology.wa.gov/publications/documents/2011034.pdf)), along with many areas of the Hangman Creek watershed ([WRIA 56 summary](https://apps.ecology.wa.gov/publications/documents/2011056.pdf)).

So when you look at the reports near your land, give the newest ones the most weight.

## How We Estimate the Depth for Your Property

No one can say exactly how deep a well will go until it's drilled, but the wells around your land are the best evidence there is. Send us the address or parcel number. We'll check the well reports nearest your land and give you a free estimate. It includes a realistic depth for your property.

We look at how deep each nearby well went, where its water settled, its tested yield, what the driller went through and when it was drilled. Wide swings between neighbors mean budgeting toward the high end. Before drilling, we pick the exact spot with you on site, checking rig access and setbacks (see [choosing a well location](https://springcreekdrilling.com/guide/choosing-the-right-location-for-your-water-well/)).

## How to Look Up Well Reports Near You

You can see the same records we do. Ecology's [Well Report Viewer](https://ecology.wa.gov/regulations-permits/guidance-technical-assistance/well-report-viewer) searches by parcel number, address, owner name, county, township, range and section, or well tag number. The owner name is whoever owned the land when the well was drilled, and locations are only accurate to the township, range and section (a section is roughly a square mile), so look at the whole section around your land. In each report, check:

- the total depth and the casing depth;
- the static water level and the tested yield, in [gallons per minute](https://springcreekdrilling.com/guide/how-many-gallons-per-minute-should-a-well-produce/);
- what the driller went through, and where water showed up;
- the completion date, since newer reports best reflect today's water levels.

Our guide to [understanding your well report](https://springcreekdrilling.com/guide/understanding-your-well-report/) walks through each section.

## Get a Depth Estimate for Your Land

County and town numbers are a starting point; the wells around your property tell the real story. Send us the address or parcel number. We'll check the well reports nearest your land and give you a free estimate. We drill new and replacement [home wells](https://springcreekdrilling.com/residential-well-drilling/) across Spokane, Stevens and Lincoln counties and handle the notice of intent and the well report as part of the project. [Request your free estimate](https://springcreekdrilling.com/get-estimate/).
