# Water Well Drilling in Kettle Falls, WA

URL: https://springcreekdrilling.com/well-drilling/kettle-falls-wa/
Last updated: 2026-11-01

Kettle Falls sits on Lake Roosevelt where the Colville River reaches the Columbia, and three watersheds meet around it. Wells here run deeper, and vary more, than almost anywhere else in Stevens County. Here's what the state's records show and how the water rules sort out.

[Get a free estimate](https://springcreekdrilling.com/get-estimate/) [Call (509) 319-4713](tel:+15093194713)

A typical well around Kettle Falls. It's 245 ft deep. Water fills the well up to about 70 ft below the ground (the blue). Half the wells here are 120 to 392 ft deep, shown by the bracket. Based on state well records.

## Well data for Kettle Falls

From 493 water well reports filed with the Washington State Department of Ecology.

- Median well depth: 245 ft (Half are 120–392 ft deep)
- Water well reports: 493 (31 drilled since 2020)
- Median depth to water: 70 ft (Static water level at completion)
- Median well yield: 8 gpm (Gallons per minute at completion)

How deep wells run around Kettle Falls

- Under 100 ft 19% of wells (87)
- 100–199 ft 21% of wells (97)
- 200–299 ft 18% of wells (86)
- 300–399 ft 19% of wells (87)
- 400–599 ft 16% of wells (77)
- 600 ft or more 8% of wells (36)

Wells drilled since 2015 have a median depth of 270 ft, deeper than the 201 ft median for wells drilled before 2000.

Source: [Washington State Department of Ecology well reports](https://fortress.wa.gov/ecy/gispublic/DataDownload/WR%5FGEO%5FWellReports.htm), records through February 2025. Counts wells closer to Kettle Falls than to any other community we track, within 10 miles. Depths, water levels and yields are as the drillers reported them (59 reports list a water level and 68 list a yield). Report locations are accurate to about 40 acres. These figures describe the area, not your property: we check the reports nearest your site before we quote.

## Deep Wells, Wide Range

The state has 493 water well reports for the area around Kettle Falls. The median well is 245 feet deep, one of the deepest medians in Stevens County, and the spread is the widest in the county: half of the wells are between 120 and 392 feet, and one in ten goes deeper than 522 feet. Water typically settles about 70 feet below the surface, and the median tested yield is 8 gallons per minute.

East of town the median is 200 feet and to the south 220 feet. To the southeast and southwest, wells go deeper, with medians of 280 and 300 feet. Before we give you an estimate, we look up the well reports filed for the properties closest to yours.

## Three Watersheds Meet Here

Ecology's watershed boundaries split at the mouth of the Colville River, so the area around Kettle Falls falls into three:

- **Colville River watershed (WRIA 59):** about 65% of the well reports, with a median depth of 220 feet.
- **Middle Lake Roosevelt (WRIA 58)**, draining to the lake downstream of the Colville River: about 24%, with a median of 300 feet.
- **Upper Lake Roosevelt (WRIA 61)**, between the mouth of the Colville River and the Canadian border: about 11%, with a median of 274 feet.

Water is scarce in all three. Ecology says groundwater from bedrock in the Middle Lake Roosevelt watershed is "very limited by climate and geology" ([WRIA 58 summary](https://apps.ecology.wa.gov/publications/documents/2011058.pdf)), and that in the Upper Lake Roosevelt watershed, where precipitation ranges from 21 inches a year near Kettle Falls to more than 55 in the mountains, "only a fraction of this precipitation becomes groundwater" ([WRIA 61 summary](https://apps.ecology.wa.gov/publications/documents/2011061.pdf)).

## The Clay Under the Valley

The U.S. Geological Survey's study of the Colville River watershed found a thick layer of lake-bed clay and silt along the valley floor, and its greatest recorded thickness, more than 400 feet, is in areas near Addy and Kettle Falls. Below it lies a lower sand and gravel aquifer that USGS believes reaches the mouth of the watershed and discharges into Lake Roosevelt. Between Colville and Kettle Falls, USGS found the groundwater gradient becomes much steeper, 60 to 200 feet per mile ([USGS SIR 2004-5237](https://pubs.usgs.gov/sir/2004/5237/section3.html)). A thick clay layer is one reason a well can go a long way before it reaches water worth finishing in.

## Water Rules

- **In the Colville watershed:** a new home on a new permit-exempt well is limited to an annual average of 3,000 gallons a day, with no more than 5,000 on any day, and the county collects a $500 fee with the building permit ([RCW 90.94.020](https://app.leg.wa.gov/RCW/default.aspx?cite=90.94.020)). Wells drilled before January 19, 2018 aren't affected.
- **In the Lake Roosevelt watersheds:** the standard exemption applies, up to 5,000 gallons a day for household use without a water right, but Ecology notes it "may not be available to prospective water users in certain areas" that have been closed, so check with Ecology's Eastern Region office for a specific parcel.

## What Stevens County Needs Before You Build

Stevens County Land Services' [guide to potable water requirements](https://files.municipalone.com/stevenscounty-wa/GuidetoPotableWaterRequirements1341061030082720PM.pdf) asks for at least 800 gallons a day for a single home, held over four hours, and lab results less than two years old from a state-certified lab showing no coliform bacteria and nitrate, arsenic, lead and uranium within limits. The Northeast Tri-County Health District adds that uranium "is especially common throughout Ferry, Stevens and Pend Oreille Counties" and recommends re-testing for it every three to five years ([NETCHD](https://www.netchd.org/241/Drinking-Water-Wells)).

## Planning Your Budget

Depth is the biggest factor in what a well costs, and around Kettle Falls it ranges more than anywhere else in the county. Our [guide to the cost of drilling a well](https://springcreekdrilling.com/guide/the-cost-of-drilling-a-well/) covers the rest. We also drill around [Colville](https://springcreekdrilling.com/well-drilling/colville-wa/), about 8 miles away. For a number specific to your property, send us the address or parcel number, and we'll check the nearby well reports and give you a free estimate.

## Questions about well drilling around Kettle Falls

### How deep are wells around Kettle Falls?

Across 470 well reports, the median is 245 feet, one of the deepest in Stevens County, and half of the wells are between 120 and 392 feet, the widest range in the county. East of town the median is 200 feet; to the southwest it's 300 feet. We check the reports nearest your property before we quote.

### Can I use a permit-exempt well near Lake Roosevelt?

It depends on the parcel. For the Lake Roosevelt watersheds on either side of Kettle Falls, Ecology notes that the permit exemption "may not be available to prospective water users in certain areas" that have been closed because there is limited or no water available, and it asks people to check with its regional office. Ecology's Eastern Region office in Spokane can tell you about a specific parcel. [Ecology's WRIA 61 summary](https://apps.ecology.wa.gov/publications/documents/2011061.pdf).

### Do the Colville watershed rules apply in Kettle Falls?

In about 65% of the area, yes. In the Colville watershed, a new home on a new permit-exempt well is limited to an annual average of 3,000 gallons a day and the county collects a $500 fee with the building permit. The Lake Roosevelt watersheds aren't covered by that part of the 2018 streamflow law, so the standard exemption of up to 5,000 gallons a day applies there, where the exemption is available.

### How soon can you drill a well near Kettle Falls?

Kettle Falls is about 66 miles from our base in Reardan, within our service area. Most of our projects are scheduled within weeks, not months, and once we're on site, most wells take one to three days. [Request a free estimate](https://springcreekdrilling.com/get-estimate/) or call [(509) 319-4713](tel:+15093194713).
