Skip to main content

Water Well Drilling in Colville, WA

Colville is the county seat of Stevens County and has more well reports around it than any other community in the county. Here's what the state's records show about drilling around Colville, how the valley's aquifers work, and what the county asks for before you build.

Simplified drawing of the ground and a typical well Ground around Colville: Glacial sand, gravel and clay in the valleys, with bedrock below and on the higher ground. A typical well reaches 171 feet. Surface 100 ft 200 ft 300 ft 400 ft 500 ft Typical well 171 ft Half of wells 82–300 ft Water fills to 50 ft Water fills to Unknown
A typical well around Colville It's 171 ft deep. Water fills the well up to about 50 ft below the ground (the blue). Half the wells here are 82 to 300 ft deep, shown by the bracket. Based on state well records.

Well data for Colville

From 1,181 water well reports filed with the Washington State Department of Ecology.

Median well depth
171 ft
Half are 82–300 ft deep
Water well reports
1,181
59 drilled since 2020
Median depth to water
50 ft
Static water level at completion
Median well yield
6 gpm
Gallons per minute at completion
How deep wells run around Colville
  • Under 100 ft 30% of wells (333)
  • 100–199 ft 23% of wells (249)
  • 200–299 ft 17% of wells (187)
  • 300–399 ft 12% of wells (135)
  • 400–599 ft 13% of wells (143)
  • 600 ft or more 4% of wells (47)

Wells drilled since 2015 have a median depth of 215 ft, deeper than the 160 ft median for wells drilled before 2000.

Source: Washington State Department of Ecology well reports, records through February 2025. Counts wells closer to Colville than to any other community we track, within 10 miles. Depths, water levels and yields are as the drillers reported them (117 reports list a water level and 150 list a yield). Report locations are accurate to about 40 acres. These figures describe the area, not your property: we check the reports nearest your site before we quote.

Wells Around Colville

The state has 1,181 water well reports for the area around Colville, and 59 of them are for wells drilled since 2020. The median well is 171 feet deep, and the range is wide: half of the wells are between 82 and 300 feet, and one in ten goes deeper than 460 feet. Water typically settles about 50 feet below the surface, and the median tested yield is 6 gallons per minute.

Better Yields to the North, Less Water to the East

North of town the median well is 120 feet deep with a median yield of 15 gallons per minute, and northeast of town 140 feet. East and southeast of town, wells go deeper (204 and 190 feet) and produce much less: the median tested yields there are 2 and 3 gallons per minute. Wells drilled east of town since 2015 have a median depth of 310 feet.

Those are area medians, and neighboring properties can differ a lot. Before we give you an estimate, we look up the well reports filed for the properties closest to yours, including what those wells produced.

The Valley's Layered Aquifers

The U.S. Geological Survey's study of the Colville River watershed (USGS SIR 2004-5237) describes several kinds of ground under the area:

  • An upper outwash aquifer of glacial sand and gravel, found mostly in the stream valleys and terraces that feed the Colville River. USGS calls it "discontinuous but ... a productive and widely used source of water supply." It averages about 100 feet thick and is thickest in the tributary valleys on the east side of the Colville valley.
  • A thick clay layer under the valley floor. The Colville Valley confining unit, mostly lake-bed clay and silt, runs the length of the valley and averages about 150 feet thick.
  • A lower aquifer of sand and gravel beneath that clay, likely continuous along the valley. It's confined in most places, and many wells completed in it flow at the land surface.
  • Bedrock, which in most of the watershed is at or near the surface and is the only source of groundwater there. It "typically has very low permeabilities, except where it is fractured," and those fractures "can produce small but usable quantities of water."

Water Rules in the Colville Watershed

Colville is in the Colville River watershed (WRIA 59), one of the watersheds covered by the state's 2018 streamflow law (RCW 90.94.020). For a new home on a new permit-exempt well, indoor and outdoor use combined is limited to an annual average of 3,000 gallons a day, with no more than 5,000 on any single day, and the county collects a $500 fee with the building permit. Wells drilled before January 19, 2018 aren't affected.

Larger uses are harder. Ecology describes the Colville's tributaries as "generally closed to new water uses" and the Colville River as closed from July 16 to September 30 each year (Ecology's WRIA 59 summary). For the new homes the law allows, the watershed plan Ecology adopted in 2020 relies on projects to offset their water use, and Ecology's 2024 review found the completed projects already offset more than the projected use (Ecology publication 24-11-011).

What Stevens County Needs Before You Build

Stevens County Land Services' guide to potable water requirements asks for at least 800 gallons a day for a single home, held over four hours, shown by a well log, a pump test by a licensed driller or pump installer, or an owner's pump test on the county's form. The water has to test free of coliform bacteria and within limits for nitrate, arsenic, lead and uranium, at a state-certified lab, with results less than two years old. If a well falls short on quantity, the county can approve a storage system; if it falls short on quality, it can approve treatment with a recorded notice. The guide dates from 2018, so confirm the current requirements with Land Services when you apply.

Testing Your Water

The Northeast Tri-County Health District says uranium "is especially common throughout Ferry, Stevens and Pend Oreille Counties" and recommends testing for it every three to five years, along with coliform bacteria and nitrate every year and arsenic at least twice, once in summer and once in winter (NETCHD drinking water wells). If a test turns something up, we're happy to recommend local water treatment professionals.

Planning Your Budget

Depth is the biggest factor in what a well costs, and around Colville it varies a lot, from a median of 120 feet north of town to 310 feet for recent wells to the east. Our guide to the cost of drilling a well covers the rest. We also drill around Kettle Falls and Chewelah. For a number specific to your property, send us the address or parcel number, and we'll check the nearby well reports and give you a free estimate.

Questions about well drilling around Colville

How deep are wells around Colville?
What if my new well near Colville is low on water?
Are there flowing wells in the Colville valley?
How soon can you drill a well near Colville?