Skip to main content

Water Well Drilling in Valley, WA

Valley sits in the upper Colville River valley between Springdale and Chewelah, about 36 miles from our base in Reardan. Depths change a lot depending on which side of town you're on, and on parts of the valley floor a new well can flow on its own. Here's what to know before you drill.

Simplified drawing of the ground and a typical well Ground around Valley: Glacial sand, gravel and clay in the valleys, with bedrock below and on the higher ground. A typical well reaches 180 feet. Surface 100 ft 200 ft 300 ft 400 ft 500 ft Typical well 180 ft Half of wells 98–300 ft Water fills to 64 ft Water fills to Unknown
A typical well around Valley It's 180 ft deep. Water fills the well up to about 64 ft below the ground (the blue). Half the wells here are 98 to 300 ft deep, shown by the bracket. Based on state well records.

Well data for Valley

From 625 water well reports filed with the Washington State Department of Ecology.

Median well depth
180 ft
Half are 98–300 ft deep
Water well reports
625
56 drilled since 2020
Median depth to water
64 ft
Static water level at completion
Median well yield
6 gpm
Gallons per minute at completion
How deep wells run around Valley
  • Under 100 ft 25% of wells (150)
  • 100–199 ft 29% of wells (170)
  • 200–299 ft 20% of wells (119)
  • 300–399 ft 12% of wells (74)
  • 400–599 ft 11% of wells (68)
  • 600 ft or more 3% of wells (15)

Wells drilled since 2015 have a median depth of 204 ft, deeper than the 173 ft median for wells drilled before 2000.

Source: Washington State Department of Ecology well reports, records through February 2025. Counts wells closer to Valley than to any other community we track, within 10 miles. Depths, water levels and yields are as the drillers reported them (88 reports list a water level and 113 list a yield). Report locations are accurate to about 40 acres. These figures describe the area, not your property: we check the reports nearest your site before we quote.

Wells Around Valley

The state has 625 water well reports for the area around Valley, and 56 of them are for wells drilled since 2020. The median well is 180 feet deep, against 194 feet for Stevens County, and half of the wells are between 98 and 300 feet. Water typically settles about 64 feet below the surface, and the median tested yield is 6 gallons per minute.

Shallower to the South, Deeper to the East

Southeast and south of town, the median wells are 121 and 132 feet deep, and southwest of town 159 feet. East and northeast of town they're much deeper, with medians of 260 and 280 feet. West and northwest of town, the medians are 180 and 200 feet, and that's where much of the recent drilling has been: 51 of the 107 reports filed since 2015. Newer wells west of town have a median of 250 feet, deeper than the older ones there.

Flowing Wells on the Valley Floor

Under the Colville valley floor, the U.S. Geological Survey describes a lower sand and gravel aquifer confined beneath thick lake-bed clay. From about 3 miles north of Springdale northward, "many wells within the unit flow at land surface," a stretch that takes in Valley (USGS SIR 2004-5237). A flowing well needs more care to build. Where flowing conditions are known or suspected, state rules require a written sealing plan before drilling, with a backup method and a plan for flow that can't be controlled. The casing has to be sealed into the confining layer, and a well that flows at the surface needs a control valve that can stop the flow completely (WAC 173-160-251). We plan for that before the rig arrives.

Water Rules Around Valley

Valley is in the Colville River watershed (WRIA 59), one of the watersheds covered by the 2018 streamflow law. A new home on a new permit-exempt well is limited to an annual average of 3,000 gallons a day, with no more than 5,000 on any day, and Stevens County collects a $500 fee with the building permit (RCW 90.94.020). A home relying on a well drilled before January 19, 2018 stays under the older rules.

Ecology's rule for the watershed closes Waitts Lake, about 3 miles west of town, to new appropriations, along with the Colville River's tributaries and other lakes, and groundwater appropriations are subject to the same conditions. The USGS adds that the levels of the larger lakes, Waitts among them, likely rise and fall with the water table (Ecology's WRIA 59 summary; USGS).

What Stevens County Needs Before You Build

Before a building permit, Stevens County Land Services' guide to potable water requirements looks for at least 800 gallons a day for a single home, held over four hours, and results less than two years old from a state-certified lab showing no coliform bacteria and nitrate, arsenic, lead and uranium within limits. The county can approve storage for a well that's short on quantity, or treatment with a recorded notice for one that's short on quality. The Northeast Tri-County Health District says uranium "is especially common throughout Ferry, Stevens and Pend Oreille Counties" (NETCHD).

Planning Your Budget

Depth is the biggest factor in what a well costs, and around Valley the median runs from 121 feet southeast of town to 280 feet to the northeast. Our guide to the cost of drilling a well covers the rest. We also drill around Chewelah, about 7 miles away, and Springdale. For a number specific to your property, send us the address or parcel number, and we'll check the nearby well reports and give you a free estimate.

Questions about well drilling around Valley

How deep are wells around Valley?
What if my well flows at the surface?
Can I use water from Waitts Lake?
How soon can you drill a well near Valley?